|
|
|
|
|
|
|
|
|
|
|
|
|
Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned.
Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy.
Specs:
- 17-4 PH H900
- Q Plan B Compatible
- Atlas Adapter Overrun approximately 0.050″
- 25 Degree Taper
- 1/2-28 Threads
- 5/8-24 Threads
- H900 Wheat Finish
- Now with bigger nuts! 13/16″
- Shims Not Included, if you would like to specifically time this, shims will be required. Note: your barrel may require a shim if the manufacturer did not put a thread relief on it.
1/2x28 (SKU 10014) ** Tapered Shoulder **
5/8x24 (SKU 10013) ** Tapered Shoulder **
|
Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned.
Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy.
Specs:
- 17-4 PH H900
- Q Plan B Compatible
- Atlas Adapter Overrun approximately 0.05″
- 25 Degree Taper
- 1/2-28 Threads 25 Degree Taper Compatible
- 5/8-24 Threads 25 Degree Taper Compatible
- Black Nitride Finish (67 HRC Surface Hardness)
- Now with bigger nuts! 13/16″
- Shims Not Included, if you would like to specifically time this, shims will be required. Note: your barrel may require a shim if the manufacturer did not put a thread relief on it.
1/2x28 (SKU 10030) ** Tapered Shoulder **
5/8x24 (SKU 10029) ** Tapered Shoulder **
|
These fit the plan B type mounts. This is an updated version that has larger wrench flats on the rear. Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned.
Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy. The nitride finish does lead to a tighter seal, with that said, it is extremely important to torque and rockset your muzzle device to the barrel properly.
SPECS:
- 17-4 PH H900
- Atlas and Atlas XL Compatible
- Plan B Compatible
- Atlas Adapter Overrun Approximately 1.050″
- Atlas XL Adapter No Overrun
- 1/2-28 Threads - .375 Bore
- 5/8-24 Threads - .375 Bore
- H900 Wheat Finish (Variations Exist)
- Shims Included
1/2x28 (SKU 10043) ** Square Shoulder **
5/8x24 (SKU 10044) ** Square Shoulder **
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
These fit the plan B type mounts. This is an updated version that has larger wrench flats on the rear. Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned.
Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy.
Specs:
- 17-4 PH
- 1/2-28 Threads (.375 Bore) - SKU 10080
- 5/8-24 Threads (.375 Bore) - SKU 10082
- Now with bigger nuts! 13/16″
- Atlas adapter overrun approximately 1.050″
- Shims Not Included, if you would like to specifically time this, shims will be required. Note: your barrel may require a shim if the manufacturer did not put a thread relief on it.
1/2x28 (SKU 10080) ** 25 Degree Tapered Shoulder **
5/8x24 (SKU 10082) ** 25 Degree Tapered Shoulder **
|
These fit the plan B type mounts. This is an updated version that has larger wrench flats on the rear. Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned.
Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy. The nitride finish does lead to a tighter seal, with that said, it is extremely important to torque and rockset your muzzle device to the barrel properly.
Specs:
- 17-4 PH H900
- Plan B Adapter Overrun approximately 1.05″
- 1/2-28 Threads (.375 Bore)
- 5/8-24 Threads (.375 Bore)
- Black Nitride Finish (67 HRC Surface Hardness)
- Now with bigger nuts! 13/16″
- Shims Not Included, if you would like to specifically time this, shims will be required. Note: your barrel may require a shim if the manufacturer did not put a thread relief on it.
1/2x28 (SKU 10079) ** 25 Degree Tapered Shoulder **
5/8x24 (SKU 10081) ** 25 Degree Tapered Shoulder **
|
These fit the plan B type mounts. This is an updated version that has larger wrench flats on the rear. Always use an alignment rod to ensure that the entire system is set up correctly. Make sure all surfaces are cleaned and the muzzle device has been torqued and Rockset to the barrel. Use on a Q can voids your warranty, be warned.
Torque the muzzle device to approximately 30 ft lbs. Make sure the muzzle device is square against the shoulder. When setting the silencer on the muzzle device, ensure that the threads and tapers are clean. Torque the suppressor to 10 ft lbs. Ensure alignment. Enjoy. The nitride finish does lead to a tighter seal, with that said, it is extremely important to torque and rockset your muzzle device to the barrel properly.
SPECS:
- 17-4 PH H900
- Atlas and Atlas XL Compatible
- Plan B Compatible
- Atlas Adapter Overrun Approximately 1.600″
- Atlas XL Adapter Overrun Approximately 0.750″
- 1/2-28 Threads - .375 Bore
- 5/8-24 Threads - .375 Bore
- H900 Wheat Finish (Variations Exist)
- Shims Included
1/2x28 (SKU 10040) ** Square Shoulder **
5/8x24 (SKU 10041) ** Square Shoulder **
|
|
|
|
|
|
|
|
|
|
|
|
The Direct Thread provides a mount interface for suppressors with inside diameter threading of 1.375-24. These mounts attach directly to your barrel, no muzzle device is needed.
Specifications
- Weight: 0.72 ounces
- Threads: 1.375-24
- Titanium
- SilencerCo Bravo and other 1.375″–24 Threaded Tubes and Suppressors
- DLC + Sline coated
1/2x28 (SKU 10661)
5/8x24 (SKU 10162)
|
|
|
