|
|
|
|
|
|
|
|
|
|
|
|
|
The Strike Industries M-LOK Covers provide unlimited placement options without having to cut anything to size. With single slot pieces, you can plug any M-Lok slot you need and still have the useable slots open for ventilation or accessories, and at the same time provides more dexterity for positive weapon control with the aggressive texturing. The SI M-Lok Covers are made from a hardened nylon polymer for maximum impact absorption. If an impact is hard enough, the covers will absorb the full blow, cracking or breaking in the process in order to prevent any transmission of shock to the handguard itself. Easy to replace, these covers ensure your rail will not take impact or scratch damage under a covered area, and allow your rifle to stand up to the harshest abuse you and it will go through!
Package Includes:
Features:
- Made to fit ALL M-Lok mounting surfaces.
- Ultra-slim textured surface provides extra dexterity and positive weapon control.
- Aggressive Non-Slip or Non-Reflective surface.
- Available in Black and FDE.
- Bi-directional.
- Sacrificial cover absorbs all impact, protecting your rail system.
- Each Kit contains Five (5) matching color M-Lok Panels.
Product Codes:
SI-MLOK-COVER-V1-BK
SI-MLOK-COVER-V1-FDE
|
The Strike Industries M-LOK Covers provide unlimited placement options without having to cut anything to size. With single slot pieces, you can plug any M-Lok slot you need and still have the useable slots open for ventilation or accessories, and at the same time provides more dexterity for positive weapon control with the aggressive texturing. The SI M-Lok Covers are made from a hardened nylon polymer for maximum impact absorption. If an impact is hard enough, the covers will absorb the full blow, cracking or breaking in the process in order to prevent any transmission of shock to the handguard itself. Easy to replace, these covers ensure your rail will not take impact or scratch damage under a covered area, and allow your rifle to stand up to the harshest abuse you and it will go through!
Package Includes:
Features:
- Made to fit ALL M-Lok mounting surfaces.
- Ultra-slim textured surface provides extra dexterity and positive weapon control.
- Aggressive Non-Slip or Non-Reflective surface.
- Available in Black and FDE.
- Bi-directional.
- Sacrificial cover absorbs all impact, protecting your rail system.
- Each Kit contains Five (5) matching color M-Lok Panels.
Product Codes:
SI-MLOK-COVER-V2-BK
SI-MLOK-COVER-V2-FDE
|
The Strike Industries Extended Magazine Plate (E.M.P+5 for the PMAG M3) design provides smoother, faster magazine reloading, and handling. It provides multiple functions to include additional 5 round capacity.
Package Includes:
- 1x Enhanced Magazine Plate +5
Features:
- Finger groove for enhanced grip and easy pull from mag-well and pouch.
- Plus 5 round capacity
Product Codes:
SI-EMP-5-BK
SI-EMP-5-FDE
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
If you've ever wanted faster and reliable magazine reloads, practice makes perfect. You aren't gonna be a superstar overnight. But a little help never hurts. This is why Strike Industries has developed the Fang Trigger Guard. Our trigger guard has a stubby magazine assist "fang" that protrudes to allow with quicker and more accurate reload insertion of the magazine. The Fang Trigger Guard is made of high quality polymer and is light weight with a great look and feel that is only matched with its performance. The fang will help guide your magazine into the magwell on a much more dependable basis. It's a simple, helpful guide that can be used from the beginner to the more advanced. You have to get the feel for the timing and mechanics of a quick and clean reload, getting a competitive edge is just the smart thing to do. Try the Strike Industries Fang Trigger Guard and bite back against failed reload attempts.
Package include:
- 1 x Fang Trigger guard
- 1 x Roll Pin
- 1 x Set screw
Features:
- Nylon reinforced polymer
- Magazine reload assist
- Finger rest function
- Cleaner, faster reloads
- Use as a finger rest
- Light weight at .2 oz
Product Codes:
SI-COBRA-FANG-BK
SI-COBRA-FANG-FDE
|
The LINK Anchor Handstop is made from a heat resistant polymer that allows comfortable grip in any shooting condition. It has a low profile design that allows mounting through any MLOK or KeyMod openings. The unique tooth design allows the handstop to be reversible, giving the option for either a "push" or "pull" style grip. With the added ridges on the surface, the LINK Anchor provides unmatched dexterity from your palm to the fingertips. A true lightweight modification that is not only comfortable , has an aggressive look, and will improve accuracy over time by a stabilizing your grip.
Compatible with all MLOK / Keymod Handguards.
Product Features:
- Aggressive ergonomic grip with ridges to enhance dexterity
- Low profile, light weight, heat resistant design
- LINK attachment system
- Multi-directional attachment capabilities
Product Specifications:
- Weight: .5oz
- Height: 27mm
- Width: 22mm
- Length: 75mm
- Material: Fiber filled 30% polymer
- Finish: EDM Texture
Package Includes:
- 1X - Link Anchor
- 2X - Sets of LINK Screw & Nut
- 1X - 3/32 HEX Tool
|
The Strike Mini HandStop with Cable Management System® – a compact sized accessory for enhanced firearm control and cable organization. This lightweight, high-strength impact resistant handstop features the patent-pending SI Cable Management System® (CMS), offering versatile cable routing options, such as alongside, across, 90-degrees, U-shape or Z-shape, and excess wire storage for a clutter-free shooting experience. Designed for single M-LOK slot attachment with a compact 1.70" (43.18mm) overall length, the Strike Mini HandStop provides a rearward angle pull style grip option for superior weapon manipulation control. The textured front and rear finger areas ensure a secure grasp, while the built-in front and rear barricade stops provide additional stability. Made from the custom blended SI Polymer Extreme material, this handstop guarantees durability and performance under the most demanding conditions. Upgrade your firearm with the Strike Mini HandStop with Cable Management System® and experience the difference in control and organization.
Package Contents:
- x1 Strike Mini HandStop with Cable Management System®
- x2 Screw
- x2 Nut
- x1 Torx key [T20]
- x1 Loctite® Threadlocker Blue 243®
- x1 Warning card
Product Features:
- Built-in SI Cable Management System® (CMS) w/ excess wire storage (patent pending)
- Single M-LOK slot attachment with 1.70" (43.18mm) overall length
- Cables can be routed: alongside, across, 90-degrees, U-shape or Z-shape
- Rearward angle for pull style grip options for better weapon manipulation control
- Textured front and rear finger areas for better grasp
- Built-in front and rear barricade stop
- Lightweight
- High-strength impact resistant custom blended SI Polymer Extreme material
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Strike Industries Extended Takedown Pins and Pivot Pins are ideal for shooters looking for a custom look and that run multiple upper receivers off of a single lower. Made out of Precision-Machined Steel. This is a replacement for the standard AR15/M16/M4 takedown pins and fits most AR standard and billet receivers.
Package Includes:
- 1 x Extended Pivot pin
- 1 x Extended Take down pin
Features:
- Eliminates the need for a pin punch.
- Locks into place securely.
- Quick disassembly of the rifle.
Note: SI Extended Pivot Pins may not be a good fit for all billet receivers.
Product Codes:
SI-AR-EPTP-BK
SI-AR-EPTP-GC
SI-AR-EPTP-CC
|
The new Strike Industries Extended Latch is not only a great addition to the ARCH charging handle, it is a great addition to any standard charging handle and is the first Extended Latch constructed of aluminum to prevent wear on your receiver!!! The SI AR-LATCH ads functionality and an aggressive look to your AR without taking a toll on your bank account. With its ergonomic design it makes for an even smoother charge in extreme conditions. The quality of the Strike AR-LATCH is second to none. Once you place the AR-LATCH on your rifle, you will see, feel, and know the quality of the AR-LATCH!
Package include:
- 1 x Charging Handle Extended Latch
Features:
- Enlarged extended grasping surface for smooth operation under extreme conditions
- AR Latch co-existed with the SI ARCH for enhanced operation
- Aluminum construction for minimized weight
- Fits all Standard Mil Spec Charging Handles including the Strike Industry ARCH
Product Codes:
Black: SI-AR-LATCH-BK
Red: SI-AR-LATCH-RED
Blue: SI-AR-LATCH-BLU
|
(1) Strike Industries AR-15 Enhanced Ultimate Dust Cover
The patent pending SI UDC enables users to attach and detach the cover in 5 to 10 seconds with ease! It is constructed of a high-density polymer making it more durable and functional than the traditional dust covers. The Ultimate Dust Cover features an adjustable detent set screw in order to compensate wear on the receiver and increase or decrease opening power (To adjust detent: use small flathead driver and depress the ball detent and adjust as necessary.). Choose multiple designs to customize your AR!
NEW features of the Ultimate Dust Cover Enhanced Version include the added cut-out window on the rod for easy disassemble and that it has been made thinner than the original to be compatible with all AR15 receivers on the market and at the same time makes it even lighter weighing in at only 0.3oz!
Additionally, The "True Seal" Lip has been slightly modified to provide an even better seal then ever before! The patent pending UDC-E (Ultimate Dust Cover- Enhanced Version) is the modified version of the original UDC for mil-spec receivers.
Product Specs
- Length: 3.46in
- Weight: .3oz
- Materials: Polymer
- Color: Black or FDE
Package includes:
- 1x Dust Cover
- 1x Spring
- 1x Pin
Features:
- Patent pending spring-loaded, internal detent rod for easy installation and take-down.
- Constructed with lightweight durable polymer material weighing in at only .3oz!!!
- Cut-out window for easy disassembly on any AR15 receiver!
- Will never corrode rust or fade
- Will never deform or get bent out of shape
- Comes in a variety of designs
- Patent pending "True Seal" internal lip that seals the port tighter than traditional dust cover designs.
- Built-in adjustable detent set screw to compensate for wear on the receiver.
Product Codes:
SI-AR-UDC-E-01-223-BK
SI-AR-UDC-E-01-223-FDE
SI-AR-UDC-E-FLAG-BK
SI-AR-UDC-E-FLAG-FDE
SI-AR-UDC-E-03-223-BK
SI-AR-UDC-E-03-223-FDE
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Strike Industries Ultra Light Pivot / Takedown Pins are designed to for those looking to build the lightest AR-15 possible. They are CNC machined from 7075 aluminum making them durable and much lighter than the pins found in a standard lower receiver parts kit.
Features:
- Extended Pivot Pin Length: 1.31"
- Extended Takedown Pin Length: 1.08"
- Weight: 0.20 oz net, 0.46oz gross
- Ultra Light, 7075 aluminum construction.
- Extended grasping surface
- Colorline anodized finish
Product Codes:
SI-AR-UL-EPTP-BK
SI-AR-UL-EPTP-BLU
SI-AR-UL-EPTP-RED
SI-AR-UL-EPTP-FDE
|
The patent pending SI UDC enables users to attach and detach the cover in 5 to 10 seconds with ease! It is constructed of a high-density polymer making it more durable and functional than the traditional dust covers. The Ultimate Dust Cover features an adjustable detent set screw in order to compensate wear on the receiver and increase or decrease opening power (To adjust detent: use small flathead driver and depress the ball detent and adjust as necessary.). Choose multiple designs to customize your AR!
NEW features of the Ultimate Dust Cover Enhanced Version include the added cut-out window on the rod for easy disassemble and that it has been made thinner than the original weighing in at only 0.4oz!
Additionally, The "True Seal" Lip has been slightly modified to provide an even better seal than ever before!
Package includes:
- 1x Dust Cover
- 1x Spring
- 1x Pin
Features:
- Patent pending spring-loaded, internal detent rod for easy installation and take-down.
- Constructed with lightweight durable polymer material
- Will never corrode rust or fade
- Will never deform or get bent out of shape
- Comes in a variety of designs
- Patent pending, True Seal internal lip that seals the port tighter than traditional dust cover designs.
- Built-in adjustable detent set screw to compensate for wear on the receiver.
Note:for the AR-10 308
The SI UDC has been tested and fits on Mega Arms MATEN, DPMS Oracle, SIG 716, YHM, and SW perfectly. It is easily modified to fit other receivers with light sanding.
The 308 UDC-E is not guaranteed to fit all receivers nor be able to be modified to fit due to there being no standard for the AR10 platform.
Product Codes:
SI-AR-UDC-E-308-BK
SI-AR-UDC-E-308-FDE
|
Enhance the speed and effectiveness of the Strike Latchless Charging Handle with the ISO-Tab from Strike Industries. Made out of lightweight but durable 6061-T6 aluminum, the ISO-Tab is built like a tank but without the weight. Improve your reaction time and never miss a beat even under stressful conditions with the combination setup of a latch-less charging handle and extension tab. Choose a one-sided or ambidextrous configuration according to your needs. Featuring an aggressive texturing and a wider surface area to latch onto, never miss a step to get back into the fight.
Features:
- Enlarged, extended and textured grasping surface for easy and consistent CH manipulations under a variety of conditions.
- Interchangeable on either side.
- Available in Black, Blue, Red, and Flat Dark Earth
- Enhances operation of Strike Latchless Charging Handles
- Aluminum construction for durability and minimal added weight
- Included screw for a secure fit.
- (1) Isotab is included per package. The (1) Isotab can be installed on the right or left side of the Strike Latchless Charging Handles
Note: ONLY compatible with Strike Latch-Less Charging Handle
Note: It is highly recommended to apply threadlocker to the screw before installation.
Product Codes:
SI-ISOTAB-BK
SI-ISOTAB-BLU
SI-ISOTAB-FDE
SI-ISOTAB-RED
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Enhance your GLOCK™ to be more ergonomic and aggressive in styling with our newly released Aluminum Base Plates.
The added geometrical curves allow a more refined grip on the end of the magazine for a smoother reload. Reload with speed and style because of the added ramp structure to assist in faster removal and easier insertion of your GLOCK™ magazine.
The anodized aluminum magazine base plates weigh 0.4 oz which is super lightweight and add an additional 15mm height
The Strike Aluminum Magazine Base Plates for GLOCK™ are CNC machined from durable 6061-T6 aluminum. As an added bonus, they are legal in all states because they do not add extra rounds to your magazine. A true aesthetic upgrade for any GLOCK™ owner or Competitive Shooter.
The improved angle of our base plate will allow you to stand your magazine upright on any flat surface, creating ease of storage as well as the ability to reload single-handedly on a table or stand.
Features
- Enhanced Geometry Provides Better Grip
- Baseplate Shape Adds weight for quicker mag release
- Made from Ultra-durable 6061-T6 Aluminum
- Custom Aesthetics for shooter
Specifications
- Length:40.56mm
- Width: 30.55mm
- Height: 11.69mm Weight: .4 oz
- Finish: Anodized aluminium (Black, Red, Blue, Titan)
- Compatible with the following Glock models: 17, 17L, 19, 22, 23, 25, 31, 32, 34, 35, 37, 38,
DISCLAIMER: This product is not manufactured, authorized, endorsed,
or warranted by GLOCK. GLOCK does not warrant or represent that
this product is compatible with GLOCK pistols.
DISCLAIMER: “GLOCK” is a federally registered trademark of
GLOCK, Inc. and is one of many trademarks registered by GLOCK, Inc.
and GLOCK Ges.m.b.H. Neither Joe Bob Outfitters, LLC, nor this site
are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc.
or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to
advertise the sale of GLOCK pistols, parts, or components. For
additional genuine GLOCK, Inc. and GLOCK Ges.m.b.H products and
parts visit www.glock.com.
|
The Strike Billet Magazine Catch Assembly features a billet magazine release button. Sculpted from a solid piece of 6061 aluminum, the button offers a functional and aesthetic upgrade to your AR. Deep serrations and ergonomic shape facilitates positive engagement and identification even in the dark or adverse conditions. The blind thread and color anodized options provide for a unique, custom look to your AR.
Note: May not be compatible with all California compliant bullet buttons.
Product Specs
Materials:
- Magazine Release Button: 6061-T6 aluminum button
- Enhanced Magazine Catch: Steel
- Gross wt: 0.6 oz
- Net wt: 0.4 oz
Package includes:
- 1x Billet Magazine Release
- 1x Enhanced Magazine Catch
- 1x Magazine Catch Spring
Features:
- Textured for positive feel and manipulation
- Solid billet aluminum construction
- Functional and aesthetic upgrade
Product Codes:
SI-AR-SMC-BK
SI-AR-SMC-FDE
SI-AR-SMC-BLU
|
The Strike Industries M-LOK Cable Management Covers add a positive tactile feeling but also utilizes the patent pending SI Cable Management System® (CMS) function enables you to organize and store excess wire from your weapon light or any other cabled accessories. Instead of tucking wire anywhere you can and using cable ties or tape to hold it down, the SI CMS will offer you a place to route and/or contain loose wire inside the cover cavity. Cables can be routed alongside the handguard, across to the other side, 90-degrees or U-shape. The directions and possibilities are almost endless. Designed to be low-profile (6.20mm (0.24”) height) and used in any orientation, the contoured covers add ergonomic textured surfaces to your handguard. Made of durable and lightweight polymer, the covers are also a quick and affordable upgrade to mitigate any heat transfer between the barrel and the shooters hands while organizing and routing cables just about any way you want. Available in a Long version that is 79.80mm (3.14”) in length that comes in a 2-pack or a Short version that is 39.90mm (1.57”) in length that comes in a 4-pack. Get one length or both and always have the Strike Industries M-LOK Cable Management Covers you need to get a grip and manage your cables at the same time.
Package Contents:
- x2 M-LOK Cable Management Covers (Long) or x4 M-LOK Cable Management Covers (Short)
- x4 Screw
- x4 Nut
- x1 Torx tool [T20]
- x1 Loctite® Threadlocker Blue 243®
Product Features:
- Built-in Cable Management System® w/ excess wire storage (patent pending)
- Cables can be routed: alongside, across, 90-degrees or U-shape
- Positive tactile feeling
- Minimizes heat transfer
- Increased comfort
- Protection against sharp rail slot edges
- Made from durable and lightweight polymer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Strike Industries LINK Angled HandStop with Cable Management System® is a rearward angle setup for pull style grip options for better weapon manipulation control. This rail attachment assists in pulling the weapon into the shooters shoulder which aids in additional control and mitigating recoil. Textured front and rear finger areas for better grasp plus built-in front and rear barricade stop. The SI patented LINK system allows mounting onto both M-LOK and KeyMod compatible devices for a bigger variety of applications. Also included is the patent pending SI Cable Management System® (CMS) function which enables you to organize and store excess wire from your weapon light or any other cabled accessories. Cables can be routed alongside the handguard, across to the other side, 90-degrees or U-shape. Lightweight high-strength impact resistant custom blended SI Polymer Extreme material with a size and design to fit a wide variety of hands, the SI LINK Angled HandStop with Cable Management System® is an excellent way to increase shootability of your weapon.
COMPATIBILITY: M-LOK and KeyMod
Package Contents:
- x1 LINK Angled HandStop with Cable Management
- x2 Screw
- x2 Nut
- x1 Torx key [T20]
- x1 Loctite® Threadlocker Blue 243®
- x1 Warning card
Product Features:
- Patented SI LINK mounting system (M-LOK and KeyMod compatible)
- Built-in SI Cable Management System® (CMS) w/ excess wire storage (patent pending)
- Cables can be routed: alongside, across, 90-degrees or U-shape
- Rearward angle for pull style grip options for better weapon manipulation control
- Textured front and rear finger areas for better grasp
- Built-in front and rear barricade stop
- Lightweight
- High-strength impact resistant custom blended SI Polymer Extreme material
|
The Strike Industries Angled Vertical Grip with Cable Management is engineered like no other grip on the market. The grip angle sits on the handguard at 86 degrees. Patent pending SI cable management function enables you to organize and store excess wire from your weapon light or any other cabled accessories in multiple configurations. Instead of tucking wire anywhere you can and using cable ties or tape to hold it down, the cable management feature will offer you a place to route and/or contain loose wire inside the grip cavity. The side cuts at the top middle of the grip allow for easier pressure switch attachment. The Short version can be mounted in either direction for your own preferred and personal setup and is low-profile form helps to minimize snags. The forward angle provides more of a natural wrist angle and increased rigidity of forearm. Designed with textured palm and finger areas with flat sides for positive handling and easier manipulation of the firearm. Made from durable and lightweight polymer compatible with M-LOK rails. No messy wires.
Package Contents:
- x1 Angled Vertical Grip
- x2 #8-32x0.3" screw
- x2 M-LOK nut
- x1 Torx key
- x1 Loctite® Threadlocker Blue 242®
Product Features:
- 86° grip angle
- Built-in cable management w/ excess wire storage (patent pending)
- Forward angle provides more of a natural wrist angle and increased rigidity of forearm
- Side cuts at top of grip for pressure switch cable routing
- Low-profile design to minimize snags
- Can be mounted in either direction for preferred setup
- Textured palm and finger areas with flat sides for better weapon manipulation control
- Made from durable and lightweight polymer
- For M-LOK rails
|
The Strike Gear® S3 Sling LITE (Silent Strategic System) is a testament to minimalist design and functionality. This sling sports a streamlined 1-inch width, ensuring lightweight comfort and straightforward usability. It features twin elastic keepers for additional webbing storage and a cross-stitched handle for rapid sling length adjustment. A padded shoulder section adds to your comfort during extended use.
The integrated ladder lock buckle simplifies one-handed manipulations, while multiple tri-bar buckles provide a secure grip on the webbing and allow for customized fitment adjustments. A robust, metal loop buckle ensures a strong, non-adjustable fastening for unyielding reliability.
Available in versatile color options like Black & Coyote Brown. The S3 Sling LITE combines aesthetic appeal with tactical functionality.
NOTE: This sling DOES NOT include attachment hardware, it is compatible with all 1.25" hardware types, such as QD swivels, hooks, paraclips, and more
Package Contents:
- x1 S3 Sling Lite (Silent Strategic System)
Product Features:
- Minimalistic 1-inch width for a lightweight simple construction
- Twin elastic keepers for extra webbing storage
- Cross-stitched handle enables swift sling length changes
- Padded shoulder section enhances comfort
- Ladder lock buckle facilitates one-handed adjustments
- Multiple tri-bar buckles ensure secure webbing grip and custom fitment adjustments
- Metal loop buckle offers strong, non-adjustable fastening
- Available in Black & Coyote Brown
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(1) Strike Industries AR-15 Forward Assist
Strike Industries is proud to offer our very own Mil-Spec Forward Assist Assembly for the AR15/M16/M4. Complete with spring and roll pin. This product is manufactured from high strength carbon steel and is head treated. Perfect for upgrading your existing component or replacing worn or broken parts.
Package Includes:
Features:
- Includes the roll pin and spring
- Made of heat treated, high strength carbon steel
Product Codes:
SI-AR-FA-BK
SI-AR-FA-GC
SI-AR-FA-CC
|
The Strike Industries Slide Cover Plate for GLOCK is perfect for those who are looking for an aesthetic and functional upgrade to their GLOCK pistols. The SI Slide Cover Plate for GLOCK allows for tool-less disassembly of the firing pin and extractor using a (patent-pending) push-button design for greater ease of maintenance. Machined from aircraft grade aluminum and anodized, the SI Slide Cover Plate is significantly more durable than the factory plastic slide plate.
Package Includes:
- 1X Slide Plate for GLOCK
- 1X Slide Cover Plate Button
Features:
- Push-button design (Patent Pending)
- Tool less disassembly of GLOCK slide
- Fits GLOCK models 17-39
- Customize color match on Cover Plate and Cover Plate Button
- NOT FOR G42/43 or Gen 5 Models
Product Codes:
SI-GSP-V1-BK
SI-GSP-V1-RED
SI-GSP-V1-BLU
DISCLAIMER: This product is not manufactured, authorized, endorsed,
or warranted by GLOCK. GLOCK does not warrant or represent that
this product is compatible with GLOCK pistols.
DISCLAIMER: “GLOCK” is a federally registered trademark of
GLOCK, Inc. and is one of many trademarks registered by GLOCK, Inc.
and GLOCK Ges.m.b.H. Neither Joe Bob Outfitters, LLC, nor this site
are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc.
or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to
advertise the sale of GLOCK pistols, parts, or components. For
additional genuine GLOCK, Inc. and GLOCK Ges.m.b.H products and
parts visit www.glock.com.
|
The Strike Industries Slide Cover Plate for GLOCK is perfect for those who are looking for an aesthetic and functional upgrade to their GLOCK pistols. The SI Slide Cover Plate for GLOCK allows for tool-less disassembly of the firing pin and extractor using a (patent-pending) push-button design for greater ease of maintenance. Machined from aircraft grade aluminum and anodized, the SI Slide Cover Plate is significantly more durable than the factory plastic slide plate.
Package Includes:
- 1X Slide Plate for GLOCK
- 1X Slide Cover Plate Button
Features:
- Push-button design (Patent Pending)
- Tool less disassembly of GLOCK slide
- Fits GLOCK models 17-39
- Customize color match on Cover Plate and Cover Plate Button
- NOT FOR G42/43 or Gen5 Models
Product Codes:
SI-GSP-V2-BK
SI-GSP-V2-BLU
DISCLAIMER: This product is not manufactured, authorized, endorsed,
or warranted by GLOCK. GLOCK does not warrant or represent that
this product is compatible with GLOCK pistols.
DISCLAIMER: “GLOCK” is a federally registered trademark of
GLOCK, Inc. and is one of many trademarks registered by GLOCK, Inc.
and GLOCK Ges.m.b.H. Neither Joe Bob Outfitters, LLC, nor this site
are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc.
or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to
advertise the sale of GLOCK pistols, parts, or components. For
additional genuine GLOCK, Inc. and GLOCK Ges.m.b.H products and
parts visit www.glock.com.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Form meets function with the Strike Industries line of Aluminum trigger
guards. Not only does the sculpted, billet aluminum trigger guard make
your rifle stand out from the pack, it also provides real added value
over the competition. The Fang feature from our popular polymer trigger
guard is retained to help guide the magazine for faster, more consistent
reloads.
Contents:
- Cobra Aluminum Trigger Guard
- Roll Pin
- (4) M3 hex screw
Features:
- Aircraft grade aluminum construction
- Magazine reload assist
- Cleaner, faster reloads
- Lightweight (.4 oz with included hardware)
|
(1) Strike Industries AR-15 Strike Forward Assist
The New Strike forward assist is the latest addition to the Strike Industries line of performance AR parts. The Forward Assist Plunger is made of lightweight aluminum for those looking to retain the functionality of a forward assist, while seeking weight savings wherever they can. The forward assist pawl is constructed of tool steel to ensure positive engagement of the forward assist ratchets on compatible bolt carriers and maintain long service life.
Package includes:
- 1x Forward Assist Plunger
- 1x Forward Assist Pawl (Installed)
- 1x Forward Assist Spring (Installed)
- 1x Forward Assist Spring Pin
Features:
- Lightweight at only 0.2oz
- Anodized Red Line color
- Increased corrosion resistance
Product Codes:
SI-AR-S-FA-BK
SI-AR-S-FA-BLU
SI-AR-S-FA-RED
|
The SI Modular Guide Rod for Gen 3 Glocks is a stainless steel, customizable system that accepts any aftermarket Glock Spring as well as Strike Industries custom recoil spring weights. Its stainless steel shaft and anodized aluminum end cap will not rust, crack or break as easily as polymer rods found in OEM Glock pistols, increasing its service life compared to standard recoil assemblies. Fine tune your Glocks recoil characteristics and improve reliability by using our Glock recoil springs offered in various weights without having to buy more than one guide rod. Simply unscrew the endcap, replace the spring to your preference, replace the end cap and you're good to go!
Product Specifications:
- Shaft ID: 0.223
- OD: 0.41
- Length: 3.10 (without shims)
Contents:
- 1x GMGR : SUS303
- 3x endcaps: 7075 T6 Aluminum
- 2x 0.2mm shims: SUS304
- 1x 0.4mm shims: SUS304
Instructions: The varieties of included shims are to ensure the guide rod fits a wide variety of Glock slides. Begin with just the 0.4mm shim and test for fit and function. the shims also change how flush the end cap is to the front of the slide.
Compatibility:
Fits G17,17L,22,24,31,34,35,37
Features:
- Easily swap different spring weights.
- Made from 303 Stainless Steel for corrosion resistance and increased toughness.
- Adjustable fit with the included shims even allows compatibility with the Strike Jitterplug Glock Gen 3 upgrade.
- Endcaps available in 4 different colors, and 3 different designs.
NOTE: These are Gen 3 size Glock Guide Rods.
NOTE: Very light reduced power springs may not function 100% in stock platforms when feeding from reduced capacity magazines.
NOTE: Use of medium strength thread locker to the endcap threads during installation is highly recommended.
DISCLAIMER: This product is not manufactured, authorized, endorsed,
or warranted by GLOCK. GLOCK does not warrant or represent that
this product is compatible with GLOCK pistols.
DISCLAIMER: “GLOCK” is a federally registered trademark of
GLOCK, Inc. and is one of many trademarks registered by GLOCK, Inc.
and GLOCK Ges.m.b.H. Neither Joe Bob Outfitters, LLC, nor this site
are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc.
or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to
advertise the sale of GLOCK pistols, parts, or components. For
additional genuine GLOCK, Inc. and GLOCK Ges.m.b.H products and
parts visit www.glock.com.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Strike Industries AR Overmolded Ultimate Dust Cover for .223/5.56 is the next iteration of our Ultimate Dust Cover (UDC). The upgraded UDC design with double injection mold and overmolded rubberized soft sealing lip for better seal to prevent debris and water from entering when the cover is closed. The SI patent pending "True Seal" internal lip seals the port tighter than traditional dust cover designs. The AR Overmolded UDC comes pre-assembled with all the parts needed for a quick tool-less installation and easy disassembly using something as common as a pen or small point. Built into the UDC is an adjustable detent set screw to compensate for wear on the upper receiver. The SI patent pending noise-reduction rubber padding also makes it nearly 100% silent during activation. Made of overmolded high-strength impact resistant custom blended SI Polmer Extreme material, the SI AR Overmolded UDC does not deform or get bent out of shape. Resistant to rust unlike traditional steel covers, if the time ever comes, knowing you can remove and quickly reinstall makes this an easy cost-effective choice. Consider the Strike Industries AR Overmolded Ultimate Dust Cover for .223/5.56 on a new build or when you are going to untorque the barrel nut as this is the easiest time to remove your old stamped steel dust cover to upgrade. Install AND remove any SI UDC in just 5 to 10 seconds.
Package Contents:
- x1 AR Overmolded Dust Cover
- x4 Rubber pads
Product Features:
- Upgraded UDC design with double injection mold and overmolded rubberized seal
- Quick tool-less installation and easy disassembly using something as common as a pen
- Patent pending "True Seal" internal lip seals the port tighter than traditional dust cover designs
- Overmolded soft sealing lip for better seal to prevent debris and water from entering when cover is closed-
- Built-in adjustable detent set screw to compensate for wear on upper receiver
- Patent pending noise-reduction rubber padding makes it nearly 100% silent during activation
- Made of overmolded high-strength SI Polymer Extreme material to not deform or get bent out of shape
- Resistant to rust unlike traditional steel covers
- Install AND remove the Overmolded Ultimate Dust Cover in just 5 to 10 seconds
COMPATIBILITY:
- AR-15 Mil-Spec upper receivers
- Aero Precision M4E1
NOT COMPATIBLE:
- Upper Receivers: VLTOR MUR: Modular Upper Receiver and ZRO Delta
- Lantac Enhanced BCG due to carrier and bolt design
|
The Strike industries cobra grip was developed using innovation and feedback from combat veterans. The cobra grip is made from advanced polymer which is very strong and will definitely take a beating. The shooter can use different grip techniques and allows the user to have a secure and comfortable grip in any situation or position. It features a ridged front face that allows you to brace the rifle against a table or a wall and because it is ridged, it will prevent any sliding during the recoil kick. Another unique feature is the Cobra "hood". It acts like a heat shield that will prevent the heat from going to your hands and gives your lead hand an ergonomic platform to use. The rear portion of the Cobra Grip can function as a hand stop. One advantage that the SI Cobra Grip has over its competitors is the friction lock design. Material has been removed from the center so when tightening the Main Screw, it will allow it to grip the rail system and thus preventing any wobbling due to lose fitment or over use of the grip. The Strike industries Cobra grip is slim and low profile which makes it very light weight. Shooters from all walks of life and different size hands can use the Strike Industries Cobra Grip without worrying if the grip is too big or the angle would be too aggressive that it would strain your hand. It is very ergonomic and economical.
Product Specs:
Product Codes:
SI-CTFG-BK
SI-CTFG-FDE
|
The Strike Industries Shift Pins bring yet another innovative solution to the AR15 market. Keeping the extended grip surface for easy disassembly without a need for a pin punch, the pins are also designed with Quick Detach mechanisms that result in not needing to remove your stock assembly (endplate, castle nut, buffer tube, etc.). Simply rotate, and remove the pins as shown. This new design combined with our enhanced detent pins retained inside the pin springs assist in making assembly and disassembly an almost effortless task with minimal tools and effort.
The SI Shift Pin is CNC machined from solid steel for strength, precision fit and corrosion resistance. This is a replacement for the standard AR15/M16/M4 takedown pins and fits most AR standard and billet receivers.
Product Specifications:
Size:
- Pivot Pin:Length: 1.31”
- Take Down Pin:Length: 1.08”
- Weight (set): 0.52oz
- Gross Packaged Weight: 0.7oz
Materials:
Finish:
- Black: Black oxide
- Gold: Gold plating
- Chrome: Chrome Plating
Contents:
1x Pivot Pin
1x Takedown Pin
Features:
- Less steps needed to remove pins
- Eliminates the need for a pin punch.
- Locks into place securely. Innovative QD rotation feature
- Nearly tool less assembly and removal
- Combine with the enhanced detent pins for easier assembly and removal
- Quick rifle assembly and disassembly
- Improved corrosion resistance
Note: Designed around Forged Mil-Spec receivers. May not fit some billet lower receivers.
Product Codes:
SI-AR15-SHIFT-BK
SI-AR15-SHIFT-GC
SI-AR15-SHIFT-CC
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Strike Industries Mag Release for the Gen 4 GLOCK™ is a new modular upgrade for the GLOCK™ Gen 4. Included are two push buttons that are easily interchangeable. Both button faces are CNC milled from 6061 Aluminum, with mag release internal mechanism made from high density polymer that provides smooth ejection.
Compatible with Glock Gen4 & Gen5 17 | 19 | 22 | 23 | 26 | 27 | 31 | 32 | 33 | 34 | 35 | 37 | 38 | 39
Does not fit Glock 36 | 42 | 43
Product Features:
- Includes two interchangable button heads
- Agressive texturing on push pad to prevent slippage
- Hybrid design with anodized aluminum and polymer body bar
- Main body designed with polymer to minimize wear and tear on magazine retention cut outs and polymer pistol body
Package Includes:
- 1 x Mag Release (polymer)
- 1 x Mag Release button 1 (aluminum)
- 1 x Mag Release button 2 (aluminum)
- 1 x M2 Screw
DISCLAIMER: This product is not manufactured, authorized, endorsed,
or warranted by GLOCK. GLOCK does not warrant or represent that
this product is compatible with GLOCK pistols.
DISCLAIMER: “GLOCK” is a federally registered trademark of
GLOCK, Inc. and is one of many trademarks registered by GLOCK, Inc.
and GLOCK Ges.m.b.H. Neither Joe Bob Outfitters, LLC, nor this site
are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc.
or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to
advertise the sale of GLOCK pistols, parts, or components. For
additional genuine GLOCK, Inc. and GLOCK Ges.m.b.H products and
parts visit www.glock.com.
|
Strike Industries LINK attachment system takes the age old question Key-Mod vs. M-Lok and came up with the ultimate solution, a dual interface design compatible with both M-Lok and Key-Mod, same hardware with no need for additional parts. This Aluminum rail section allows the attachment of various M1913 Picatinny spec rail-mounted accessories such as vertical grips, lights, lasers, etc. The Dual interface rail section also features beveled ends to reduce snagging and eliminate sharp corners and edges.
Product Spec:
- Length: 2.55"
- Width: 0.83"
- Height: 0.36"
- Weight: 0.8oz (without screws and nuts)
- 1.0oz (including screws and nuts)
- Materials: Aluminum
Package Includes:
- Link-RS-6: 1 x rail section 6 slots
Features:
- Quickly attached from the outside of the handguard.
- 6061 Aluminum construction
- Black hard anodizing finish
- Fits both KeyMod and M-Lok mounting surfaces.
- Easy installation and removal
Product Codes:
SI-LINK-RS-6-BK
SI-LINK-RS-6-RED
|
Compatible with both KeyMod and MLOK, our Link Angled QD mount offers a natural push and pull installation/removal alongside the rail at 30 degrees instead of driving the QD socket 90 degrees flat into the rail. Once installed, the Link Angled QD retains an unobtrusive angle while slung to avoid binding with other firearms accessories and support hand while in the firing position.
Features:
- 30 degree QD mount with anti-rotation built in
- Angled for easier ergonomic placement & accessibility
- Durable aircraft grade aluminum construction
- Low-profile, snag-free, and features the LINK mounting system (M-Lok and Keymod compatible)
Product Spec (Dimensions):
- Length: 35 mm
- Height: 14 mm
- Width: 16 mm
- Weight: 0.3 oz
- Keymod Slots needed for install: 3
- M-Lok Slots needed for install: 1
Package includes:
- 1x Link AQD mount
- 1x Link T-Nut and allen screw
- 1x blue thread locker packet
|
|
|
