 |
 |
 |
|
The Strike Industries G.U.M. Universal (Optics) Mount for GLOCK™ V2
This mount has been updated to allow additional compatibility with even more red dots on the market. Its minimal super low-profile design offers a sleek appearance with our patented SI Multi-Optic Mount pattern which accommodates most Mini/Micro Red Dot Sights (MRDS).
Included mounting posts and screws provide versatility for a variety of red dot sights, while the mount's solid S45C steel construction ensures durability and long-lasting performance for holding zero. Additionally, this mount boasts the lowest height-over-bore mount in the industry, allowing for optimal accuracy and precision.
How does it work?
The G.U.M. V2 attaches via the rear dovetail on any Glock™ or aftermarket slide made for Glocks. There are a total of eight set screws that come pre-installed in the mounting plate. Two set screws are for the rear dovetail. In conjunction with the two set screws, you use the remaining set screws throughout the plate to balance it on your slide prior to installing your desired optic. NOTE: Do not use a rear sight pusher to install the G.U.M., we recommend using a nylon gunsmithing hammer to gently tap it into place. Please watch our installation video below.
Why consider this universal optic mount?
Our Glock Universal Mount provides an affordable investment as a mounting solution for users who haven't yet purchased an optics ready slide or aren't planning on getting their slide milled for an optic cut just yet. By opting for the G.U.M V2, users can test more optics without committing to any single footprint (milling your slide for an optics cut also voids the OEM warranty). Start shooting with optics today, what are you waiting for?
Package Contents:
- x1 G.U.M. Universal (Optics) Mount for GLOCK™ Version 2
- x8 G.U.M. mount set screw [M3x3mm 2.5mm Socket]
- x3 Screw [M3x8mm T10 Flat]
- x3 Screw [M3x9mm T10 Flat]
- x3 Screw [M3x10mm T10 Flat]
- x3 Screw [M3x8mm T14 Flat]
- x3 Screw [M3x8mm T15 Flat]
- x3 Screw [M3x7mm T10 Rounded]
- x3 Screw [M3x8mm T10 Rounded]
- x3 Screw [M3x10mm T10 Rounded]
- x3 Screw [M3x10mm T11 Rounded]
- x5 Large mounting post
- x5 Small mounting post
- x5 Shallow mounting post
- x3 Tall mounting post
- x1 Torx tool [T10]
- x1 Hex tool [1.5mm]
- x1 Loctite® Threadlocker Blue 243®
- x1 Warning card
Product Features:
- Minimal super low-profile design
- SI Multi-Optic Mount fits most Mini/Micro Red Dot Sights (MRDS) in the market
- No permanent milling or custom work required on slide
- Included mounting posts and screws offer versatility for various red dot sights
- Lowest height-over-bore mount in the industry
- Solid S45C steel construction and black phosphate finish
DISCLAIMER: This product is not manufactured, authorized, endorsed,
or warranted by GLOCK. GLOCK does not warrant or represent that
this product is compatible with GLOCK pistols.
DISCLAIMER: “GLOCK” is a federally registered trademark of
GLOCK, Inc. and is one of many trademarks registered by GLOCK, Inc.
and GLOCK Ges.m.b.H. Neither Joe Bob Outfitters, LLC, nor this site
are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc.
or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to
advertise the sale of GLOCK pistols, parts, or components. For
additional genuine GLOCK, Inc. and GLOCK Ges.m.b.H products and
parts visit www.glock.com.
⚠
WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer and reproductive harm. For more information go to: www.P65Warnings.ca.gov.
|
|
|
 |
|
 |
|
